G2 Axle and Gear
Showing 385–421 of 421 results
-
Uncategorized
G2 Dana 30 Brute Aluminum Finned Diff Cover – 40-2031MB
- Dana 30 front axle
- Cast from lightweight aluminum
- Black powder coat finish
- Ball milled reinforcing ribs
- Heat treated and shot peened helps handle direct impact
- Fully machined seal surface for a leak free installation
- Convenient filler plug for easy service
- Fill level plug for accurate fill level for both high and low pinion axles
SKU: G/240-2031MB -
Uncategorized
G2 Ford 9.75 Inch Aluminum Cover – 40-2012AL
- For Use On Ford 9.75in. Rear Axles
- Cast From Lightweight Aluminum To Dissipate Heat
- Raw Aluminum Finish
- ReinForcing Ribs For Added Rigidity And Strength
- Heat Treated And Shot Peened To Help Handle A Direct Impact
- Fully Machined Seal Surface For A Leak Free Installation
SKU: G/240-2012AL -
Ring and Pinion Installation Kits
AAM Master Conversion Rear Install Kit
- For Use In Dodge Ram 2500 3/4 Ton (2014 – 2016) Rear Only
- To use early style 11.5″ ring and pinion in New 11.8″ housing
- Pinion Nut
- Pinion Seal
- Timken Outer Pinion Bearing And Race Crush Sleeve
- Timken Inner Pinion Bearing and Race Pinion Shims
- Carrier Shims
- Carrier Bearings and Races
- Ring Gear Bolts
- Thread Locking Compound
- Gear Marking Compound
- Silicone Sealer
SKU: G/235-2024C -
Uncategorized
G2 Ford 8.8 Inch Aluminum Cover – 40-2013AL
- For Use On Ford 8.8in. Rear Axles
- Cast From Lightweight Aluminum To Dissipate Heat
- Raw Aluminum Finish
- ReinForcing Ribs For Added Rigidity And Strength
- Heat Treated And Shot Peened To Help Handle A Direct Impact
- Fully Machined Seal Surface For A Leak Free Installation
SKU: G/240-2013AL -
Dana 44 Axle Shafts, Replacement Axle Shafts
G2 Dana 30/44 Chromalloy Outer Axle Shaft – 97-2032-001
Dana 44 Axle Shafts, Replacement Axle ShaftsG2 Dana 30/44 Chromalloy Outer Axle Shaft – 97-2032-001
- G2 Axle and Gear Chromoly Outer Axle Shaft
- Dana 30/44
- 27 Spline
- 8.72″” Overall Length
- Accepts 5-760X U-Joint
- Driver and Passenger Side
- Machined to Accept Full Circle Clips
- For use in 72-86 Jeep CJ, Scout Dana 44
SKU: G/297-2032-001 -
Ring and Pinions
G2 XJ Cherokee Front and Rear 4.56 Ring and Pinion Kit – 4-XJ6-456
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 Short 4.56 (3.73 and up carrier)
- Rear Chrysler 8.25in 4.56
- 4.56 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ6-456 -
Dana 44 Axle Shafts, Replacement Axle Shafts
G2 Dana 44 Replacement Axle Shaft – 95-2033-1-301
- G2 Axle and Gear Dana 44 Replacement Axle Shaft
- Dana 44
- 30 Spline
- 29.25in. Overall Length
- 5 on 4.5in. & 5 on 5.5in. Bolt Circle
- Driver Side
- 1/2in. X 20 UNF Wheel Studs needed
- For use in 97-06 Jeep TJ w/Dana 44 Option
SKU: G/295-2033-1-301 -
Ring and Pinions
G2 XJ Cherokee Front and Rear 4.10 Ring and Pinion Kit – 4-XJ4-410
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 reverse 4.10 (3.73 and up carrier)
- Rear Dana 44 4.09 (3.91 and up carrier)
- 4.10 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ4-410 -
Dana 44 Differential Covers
G2 Dana 44 Aluminum Cover Black – 40-2033ALB
- For Use On Dana 44 Front Or Rear Axles
- Cast From Lightweight Aluminum To Dissipate Heat
- Black Powder Coat Finish
- ReinForcing Ribs For Added Rigidity And Strength
- Heat Treated And Shot Peened To Help Handle A Direct Impact
- Fully Machined Seal Surface For A Leak Free Installation
SKU: G/240-2033ALB -
Ring and Pinions
G2 XJ Cherokee Front and Rear 4.56 Ring and Pinion Kit – 4-XJ5-456
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 reverse 4.56 (3.73 and up carrier)
- Rear Chrysler 8.25in 4.56
- 4.56 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ5-456 -
Uncategorized
GM 12 9.5/9.76 Aluminum Differential Cover
- GM 12 bolt 9.5/9.76″ axle
- Cast from lightweight aluminum
- Black powder coat finish
- Ball milled reinforcing ribs
- Heat treated and shot peened helps handle direct impact
- Fully machined seal surface for a leak free installation
- Convenient filler plug for easy service
- Fill level plug for accurate fill level for both high and low pinion axles
SKU: G/240-2091MB -
Uncategorized
G2 GM 8.5 Inch/8.6 Inch 10 Bolt Ball Milled Aluminum Cover – 40-2021MB
- For Use On GM 8.5in. And 8.6in. Rear Axles Only
- Cast From Lightweight Aluminum To Dissipate Heat
- Black Powder Coated Finish
- Ball Milled ReinForcing Ribs For Added Rigidity And Strength
- Heat Treated And Shot Peened To Help Handle A Direct Impact
- Fully Machined Seal Surface For A Leak Free Installation
- Convenient Filler Plug For Easy Service
- Fill Level Plug For Accurate Fill Level
- Drain Plug For Mess Free Service
- Easy To Use Dipstick For Simple Maintenance
SKU: G/240-2021MB -
Ring and Pinions
G2 XJ Cherokee Front and Rear 4.10 Ring and Pinion Kit – 4-XJ6-410
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 Short 4.10 (3.73 and up carrier)
- Rear Chrysler 8.25in 4.10
- 4.10 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ6-410 -
-
Dana 44 Differential Covers
G2 Dana 44 Aluminum Cover – 40-2033AL
- For Use On Dana 44 Front Or Rear Asxles
- Cast From Lightweight Aluminum To Dissipate Heat
- Raw Aluminum Finish
- ReinForcing Ribs For Added Rigidity And Strength
- Heat Treated And Shot Peened To Help Handle A Direct Impact
- Fully Machined Seal Surface For A Leak Free Installation
SKU: G/240-2033AL -
Dana 44 Axle Shafts, Replacement Axle Shafts
G2 Dana 30/44 Chromalloy Outer Axle Shaft – 97-2031-001
Dana 44 Axle Shafts, Replacement Axle ShaftsG2 Dana 30/44 Chromalloy Outer Axle Shaft – 97-2031-001
- G2 Axle and Gear Chromoly Outer Axle Shaft
- Dana 30/44
- 27 Spline
- 6.15″” Overall Length
- Accepts 5-760X U-Joint
- Driver and Passenger Side
- Machined to Accept Full Circle Clips
- For use in Jeep XJ/YJ/TJ w/5-760X U-Joint
SKU: G/297-2031-001 -
Ring and Pinions
G2 XJ Cherokee Front and Rear 4.10 Ring and Pinion Kit – 4-XJ3-410
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 Short 4.10 (3.73 and up carrier)
- Rear Dana 35 4.11 (3.54 and up carrier)
- 4.10 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ3-410 -
Ring and Pinions
G2 XJ Cherokee Front and Rear 4.56 Ring and Pinion Kit – 4-XJ3-456
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 Short 4.56 (3.73 and up carrier)
- Rear Dana 35 4.56 (3.54 and up carrier)
- 4.56 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ3-456 -
-
Dana 44 Ring and Pinion, Ring and Pinions
G2 XJ Cherokee Front and Rear 4.88 Ring and Pinion Kit – 4-XJ4-488
Dana 44 Ring and Pinion, Ring and PinionsG2 XJ Cherokee Front and Rear 4.88 Ring and Pinion Kit – 4-XJ4-488
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 Reverse 4.88 (3.73 and up carrier)
- Rear Dana 44 4.89 (3.91 and up carrier)
- 4.88 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ4-488 -
Dana 44 Axle Shafts, Replacement Axle Shafts
G2 Dana 44 Chromalloy Inner Axle Shaft – 97-2045-002
- G2 Axle and Gear Chromoly Inner Axle Shaft
- Dana 44
- 30 Spline
- 31.88″” Overall Length
- Accepts 5-760X U-Joint
- Passenger Side
- Machined to Accept Full Circle Clips
- For use in 03-06 Jeep Dana 44 w/Rubicon Option
SKU: G/297-2045-002 -
Uncategorized
JEEP JK FRONT CORE 44 METRIC HOUSING ADDED CASTER 4″-UP LIFT
- G2 Axle and Gear CORE 44 Housing, Front Bolt in Replacement
- High Pinion
- Added caster for 4in. and higher Lift Kit
- Uses Metric carrier bearings to allow the use of factory Air Locker
- 3in. X .25in. DOM Heavy Duty axle tubes
- 3/8in. CNC-formed Heavy Duty Brackets
- Spanner Nuts for backlash adjustment
- Heavy Duty Forged Bearing Caps
- Massive Forged inner C-end’s
SKU: G/267-2051JKFL -
Dana 44 Ring and Pinion, Ring and Pinions
G2 XJ Cherokee Front and Rear 4.56 Ring and Pinion Kit – 4-XJ4-456
Dana 44 Ring and Pinion, Ring and PinionsG2 XJ Cherokee Front and Rear 4.56 Ring and Pinion Kit – 4-XJ4-456
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 reverse 4.56 (3.73 and up carrier)
- Rear Dana 44 4.56 (3.91 and up carrier)
- 4.56 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ4-456 -
Uncategorized
G2 Core 44 Rear Axle Housing – 67-2052TJR
- Fits 1997 to 2006 TJ Wrangler and LJ Wrangler Unlimited
- Bolt-in application
- Bare axle housing
- Includes G2 diff cover
- To be used with JK Ring and Pinion
- 3 inches x 5/16 inches DOM heavy-duty axle tubes
- 3/8 inch CNC-formed heavy-duty brackets
- Spanner nuts for easy backlash adjustment
- Heavy-duty forged bearing caps
SKU: G/267-2052TJR -
Ring and Pinions
G2 XJ Cherokee Front And Rear 4.10 Ring and Pinion Kit – 4-XJ2-410
- Front Dana 30 reverse 4.10 (3.73 and up carrier)
- Rear Dana 35 4.11 (3.54 and up carrier)
- 4.10 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ2-410 -
Ring and Pinions
G2 XJ Cherokee Front and Rear 4.10 Ring and Pinion Kit – 4-XJ-410
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 reverse 4.10 (3.73 and up carrier)
- Rear Dana 35 4.11 (3.54 and up carrier)
- 4.10 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ-410 -
Dana 44 Axle Shafts, Replacement Axle Shafts
G2 Dana 44 JK 07-09 Replacement Axle Shaft – 95-2052-1
- G2 Axle and Gear Jeep JK Dana 44 Replacement Axle
- Forged 1541H Steel
- 31.50in. Overall Length
- 30 Spline
- Brake Pilot Surface 2.828in.
- Bearing 1.565in.
- 5 on 5
- LH/RH
- For use in 07-09 Jeep JK
SKU: G/295-2052-1 -
Ring and Pinions
G2 XJ Cherokee Front and Rear 4.56 Ring and Pinion Kit – 4-XJ2-456
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 reverse 4.56 (3.73 and up carrier)
- Rear Dana 35 4.56 (3.54 and up carrier)
- 4.56 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ2-456 -
Ring and Pinions
G2 XJ Cherokee Front and Rear 4.56 Ring and Pinion Kit – 4-XJ-456
- Fits 1984 to 2001 XJ Cherokee
- Front Dana 30 reverse 4.56 (3.73 and up carrier)
- Rear Dana 35 4.56 (3.54 and up carrier)
- 4.56 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
SKU: G/24-XJ-456 -
Dana 44 Ring and Pinion, Ring and Pinions
G2 JK Front and Rear 4.56 Ring and Pinion Kit – 4-JK-456
- Non-Rubicon models
- Dana 30 front and Dana 44 rear
- 4.56 G-2 Ring And Pinion Sets
- Includes front and rear matched Master Installation Kits
- Limited Lifetime Warranty
- Computer Heat Treated 8620 Steel
- Manufactured To O.E. Specs
- Double Shot Peened
- Double Lapped
- Everything you need for installation on your Jeep
- Carrier sold seperately
SKU: G/24-JK-456
